Articles Tagged “Industrial IOT”
17 articles found
NXP FRDM-IMXRT1186 Board Packs Four Ethernet Ports for $85
NXP's $85 FRDM-IMXRT1186 pairs an 800 MHz Cortex-M7 with a 300 MHz Cortex-M33 and four Ethernet ports, including 2 Gigabit TSN, for industrial builds.
Renesas RZ/G3L MPUs Hit 1 mW Standby With Cortex-A55
Renesas' new RZ/G3L and RZ/G3SE run four Cortex-A55 cores at 1.2 GHz and drop to roughly 1 mW in deep standby, from $14.28 in volume pricing.
Wi-Fi HaLow USB Adapters Bring 802.11ah to Any PC
Morse Micro's MM8108-based USB adapters add sub-1 GHz Wi-Fi HaLow to a PC or router for $58, with up to 43.3 Mbps and roughly ten times normal Wi-Fi range.
Opener Brings an Open Source DECT NR+ Stack to Zephyr
Opener is an Apache 2.0 DECT NR+ stack for Zephyr, targeting a standard rated for one million devices per square kilometre on Nordic nRF91 hardware.
Nordic nRF93M1 Dev Kit Brings LTE Cat 1 bis for $60
Nordic's nRF93M1 development kit pairs a 10 Mbps LTE Cat 1 bis modem with an nRF54L15 host MCU, and prices start at $60 with a trial SIM card.
Quectel Android 16 Modules Bring 5G to IoT Devices
Quectel's SH602FA and SE505FE put production-ready Android 16 on MediaTek silicon, with 5G downlinks up to 3.27 Gbps and 32MP camera support.
NXP MCX C15 MCUs Pack 16-Bit Analog Under 60 Cents
NXP's MCX C15 and C16 Cortex-M23 MCUs start under 60 cents, pair a 16-bit ADC with an on-chip op-amp, and idle at 320 nA in deep power down.
NXP MCX A5 MCUs Pair Post-Quantum Boot With Ethernet
NXP's MCX A5 pairs a 240 MHz Cortex-M33 with an integrated 10BASE-T1S PHY and post-quantum secure boot, sampling now and available in Q4 2026.
LoRaWAN QR Codes Replace Manual Key Entry at Scale
Three new LoRa Alliance specs turn LoRaWAN device onboarding into a QR scan and add relay guidance for coverage underground and behind thick walls.
Aliensense NXS Sends Robot Camera Data 15m on One Cable
The $199 Aliensense NXS carries camera video, power and CAN-FD control over a single GMSL2/3 coax up to 15 meters, with a mikroBUS socket for expansion.
Luxonis M8 Controller Box Adds Relays and CAN to OAK4
The $249 Luxonis M8 Controller Box gives OAK4 edge AI cameras 16 GPIOs, four 16A relays, CAN 2.0 and RS232 so vision systems can drive machinery directly.
ESP32-C5 Relay Board Adds RS-485 and Wi-Fi 6 for $21
The Maker Go ESP32-C5-EVB pairs four 10A relays and four opto-isolated inputs with RS-485, dual-band Wi-Fi 6, Zigbee, and Thread, starting around $15.
Olimex PICO-EVB Adds Mains Relays to Raspberry Pi Pico
Olimex's €14.95 PICO-EVB turns any Raspberry Pi Pico into an industrial controller with four 240VAC relays, four optoisolated inputs and ESPHome support.
Raspberry Pi Single Pair Ethernet HAT Adds T1S/T1L
Brechel Electronic's new Raspberry Pi HAT+ boards add 10BASE-T1S and 10BASE-T1L Single Pair Ethernet from €95, with a one-click Linux driver installer.
Calixto AM62L STAMP SOM Puts Linux on a Postage Stamp
The Calixto AM62L STAMP SOM fits dual Cortex-A53 cores at 1.25 GHz onto a 40x40 mm module for industrial automation, HMIs, and EV chargers alike.
DEBIX T62P-01: A Pi-Sized Industrial SBC on TI Sitara AM62P
The DEBIX T62P-01 industrial SBC pairs a TI Sitara AM62P SoC with dual GbE TSN, Wi-Fi 6, and real-time R5F cores in an 88x59 mm board for robotics and edge IoT.
Toradex Zinnia IoT Gateway Brings Verdin SoMs and 5G to Industrial Edge Deployments
Toradex announced the Zinnia Linux IoT gateway on May 6, 2026 — a Verdin SoM-based industrial edge platform with dual Gigabit Ethernet, optional 5G, and Torizon OS, targeting smart cities, energy infrastructure, and edge AI.