Skip to main content
The Quantum Dispatch
Back to Home
Cover illustration for WeAct Logic Analyzer V2: A $10 USB 3.0 Tool for Makers

WeAct Logic Analyzer V2: A $10 USB 3.0 Tool for Makers

WeAct's Logic Analyzer V2 is a $10 RISC-V board with 16 channels at up to 200 MHz over USB 3.0, plus a built-in debug probe mode. Here's what it offers.

Alex Circuit
Alex Circuit★Nov 13, 2026★4 min read

A logic analyzer is one of those tools every embedded developer eventually needs, and one of the first ones a hobbyist puts off buying. WeAct Studio is making that decision a lot easier. According to CNX Software's November 12 report, the WeAct Logic Analyzer V2 is a small board built on a WCH CH32H417 RISC-V microcontroller that turns any Windows or Linux PC into a 16-channel USB 3.0 logic analyzer, and it sells for about $10 on AliExpress, before shipping and taxes.

  • Channels and speed: Up to 16 channels at 4 to 200 MHz sample rate over USB 3.0, or up to 20 MHz (16 channels) and 40 MHz (8 channels) over USB 2.0
  • Capture length: Limited by PC memory, roughly 45 seconds at 200 MHz with 16 channels, or 90 seconds with 8
  • Three apps in one: Logic analyzer, USB-serial plus CMSIS-DAP v2 debug probe, or your own custom firmware
  • Size: 42.5 x 26.5 x 13 mm with a basic enclosure, powered over USB-C

What Is the WeAct Logic Analyzer V2?

At its heart is the WCH CH32H417, a dual-core RISC-V microcontroller with a QingKe V5F core at up to 400 MHz and a V3F core at up to 144 MHz, 896KB of SRAM and 960KB of flash. That chip's USB 3.0 interface is what makes the price-to-speed ratio possible, since a logic analyzer is mostly a fast pipe that streams pin states to the host PC. The 20-pin header exposes 16 GPIO lines plus four grounds, and the input range is 1.0 to 3.3V with an adjustable threshold of 0.6 to 1.5V.

Can It Decode I2C, SPI and UART?

Yes. CNX Software lists 132 protocol decoders, including UART, I2C, SPI and CAN bus. Captures run through U3LogicAnalyzer, a fork of the popular Sigrok and PulseView software, available for Windows and Linux. That means the familiar PulseView workflow most makers already know, with protocol decoding layered over the raw waveforms.

One spec note worth getting right: 200 MHz is the maximum sample rate, not the analog bandwidth. A commenter on CNX's article points out that real-world signal capture is comfortably lower than the headline figure, which is true of every logic analyzer. For the I2C, SPI and UART traffic typical of ESP32 and microcontroller projects, it is plenty.

A Debug Probe Mode Too

The second built-in app makes this more than a one-trick board. Hold the button for two seconds and it switches to a USB-serial bridge with three CDC ports at up to 9 Mbps, plus a CMSIS-DAP v2 SWD probe for flashing and debugging Arm Cortex-M targets. An onboard RGB LED shows which mode is active. The third slot, 304KB of flash, holds your own firmware, and WeAct publishes a sample user app for the MounRiver IDE, so the board can also serve as a low-cost CH32H417 development board.

Software and Openness

The PC-side programs, including the PulseView fork, a firmware upgrade tool and a DAP flasher utility, are open source. The logic analyzer and DAP firmware themselves ship as closed-source binaries, according to CNX Software. That is a reasonable tradeoff at this price for most users.

Who Should Buy It?

Anyone debugging sensor buses, bring-up on a new board like the Seeed XIAO STM32C5, or simply learning how serial protocols work will get real value here. For about the price of a lunch, you get a USB 3.0 logic analyzer and an SWD debug probe in one thumb-sized package. Shipping costs vary by region, so check the final price at checkout. For more maker hardware, head to our mini computers coverage.

Sources: CNX Software — November 12, 2026; WeAct Studio on GitHub — accessed November 12, 2026.

More Mini Computers Stories